STMicroelectronics is expanding its digital audio power amplifier portfolio with devices built around its FFX (Full Flexible Amplification) technology, targeting PC-audio and consumer-electronics designs that require efficient all-digital signal processing. The platform is intended to give engineers flexibility in channel configuration, output power and thermal layout, from desktop speakers to home-theater systems. The devices are designed for applications including active speakers and docking stations.
ST's FFX technology uses an all-digital amplification path and high-efficiency operating modes intended to reduce system power consumption. The architecture supports binary and ternary FFX modes, allowing designers to balance efficiency and electromagnetic interference against audio fidelity for different loads.
The channel options are intended to let the same amplifier family serve compact stereo products as well as multichannel systems. For thermal management, the package choices are designed to accommodate different PCB heat paths, including designs that use a heatsink in direct contact with the package or rely on copper-area heat spreading through the board.
For different power requirements, ST offers the STA516B and STA518 four-channel power half-bridge chips. Both are aimed at home-theater systems, active speakers and docking stations, with the STA518 using Multipower BCD technology for a single-chip four-half-bridge output stage.
| Model | Key specifications | Typical applications |
|---|---|---|
| STA516B | 65 V, 7.5 A four-channel power half-bridge | Home theater, active speakers, docking stations |
| STA518 | Monolithic four-half-bridge using Multipower BCD technology | Stereo high-efficiency amplifier output stage |
The STA518 is more than a fixed power amplifier, according to ST. By connecting the CONFIG pin to the Vdd pin, designers can reconfigure the device into dual-bridge or single-bridge modes, doubling current output capability, the company says. The configuration options are intended to let one device serve different channel and power requirements.
In a single-ended configuration, the STA518 can drive a 4-ohm load with 24 W across four channels. In a BTL configuration, it provides 50 W + 50 W stereo output; in a single parallel BTL configuration, it can deliver 70 W peak power. Designers can select the mode based on load impedance and channel requirements.
The PSO36 and PSS036 surface-mount packages use Slug Up and Slug Down thermal structures. ST says the choice should be matched to the PCB's heat path, whether the design uses a heatsink in direct contact with the package or relys on copper-area heat spreading through the board.
The thermal options are intended to help maintain stability when the amplifiers operate at high output power. The FFX devices also support binary and ternary modes, which ST says can be selected according to efficiency, EMI and total harmonic distortion targets.
STMicroelectronics is expanding its digital audio power amplifier portfolio with devices built around its FFX (Full Flexible Amplification) technology, targeting PC-audio and consumer-electronics designs that require efficient all-digital signal processing. The platform is intended to give engineers flexibility in channel configuration, output power and thermal layout, from desktop speakers to home-theater systems. The devices are designed for applications including active speakers and docking stations.
ST's FFX technology uses an all-digital amplification path and high-efficiency operating modes intended to reduce system power consumption. The architecture supports binary and ternary FFX modes, allowing designers to balance efficiency and electromagnetic interference against audio fidelity for different loads.
The channel options are intended to let the same amplifier family serve compact stereo products as well as multichannel systems. For thermal management, the package choices are designed to accommodate different PCB heat paths, including designs that use a heatsink in direct contact with the package or rely on copper-area heat spreading through the board.
For different power requirements, ST offers the STA516B and STA518 four-channel power half-bridge chips. Both are aimed at home-theater systems, active speakers and docking stations, with the STA518 using Multipower BCD technology for a single-chip four-half-bridge output stage.
| Model | Key specifications | Typical applications |
|---|---|---|
| STA516B | 65 V, 7.5 A four-channel power half-bridge | Home theater, active speakers, docking stations |
| STA518 | Monolithic four-half-bridge using Multipower BCD technology | Stereo high-efficiency amplifier output stage |
The STA518 is more than a fixed power amplifier, according to ST. By connecting the CONFIG pin to the Vdd pin, designers can reconfigure the device into dual-bridge or single-bridge modes, doubling current output capability, the company says. The configuration options are intended to let one device serve different channel and power requirements.
In a single-ended configuration, the STA518 can drive a 4-ohm load with 24 W across four channels. In a BTL configuration, it provides 50 W + 50 W stereo output; in a single parallel BTL configuration, it can deliver 70 W peak power. Designers can select the mode based on load impedance and channel requirements.
The PSO36 and PSS036 surface-mount packages use Slug Up and Slug Down thermal structures. ST says the choice should be matched to the PCB's heat path, whether the design uses a heatsink in direct contact with the package or relys on copper-area heat spreading through the board.
The thermal options are intended to help maintain stability when the amplifiers operate at high output power. The FFX devices also support binary and ternary modes, which ST says can be selected according to efficiency, EMI and total harmonic distortion targets.